1. John Deere 3350 Manual

Retains the gear shift lever into the housing. Measures: 0.254 inches thick, 1.368 inch outside diameter and 0.998 inch inside diameter. 12 volt, 95 amp. 12 volt, 55 amp. Single Pulley, call if you need a double pulley. 12 volt, 55 amp. For tractor models 1030, 1040, 1130, 1140, 1350, 1530, 1550, 1630, 1640, 1750, 1840, 1850, 1850N, 1950, 1950N, (2020, 2120, 2250, 2450, 2650, 2850 euro edition), 2040, 2040S, 2140, 2150, 2155, 2240, 2255, 2350, 2355, 2355N, 2440, 2550, 2555, 2650N, 2750, 2755, 2840, 2855N, 2940, 2950, 2955, 3030, 3040, 3050, 3130, 3140, 3150, 3350, 3640, 6100, 6200, 6200L, 6300, 6300L, 6400, 6400L, 6500, 6500L, 840, 940.

John Deere technical service manuals provide detailed instructions on the repair of your. AC Compressor. If you order a John Deere manual from us. We supply john deere tractor workshop manuals and operatos manuals. Workshop Manul for John Deere 3050/3350. Workshop Manual for John Deere Tractors. 2 AC-Series Operator’s Manual-E/F Introduction THANK YOU for purchasing a John Deere product. READ THIS MANUAL carefully to learn how to operate.

(Part No: AL81436) $252.19. 12 volt, 13 tooth, clockwise rotation. For tractor models (3150 1985-87 with 6-359 dsl), (3150 built in Spain), (3155 1987-92 with 6-359 dsl), (3340 SN# 125745 & up), 3350, 3640, 3650, 5620, 6010, (6100 from 1993 & up), 6110, 6110L, (6200, 6200L, 6300, 6300L, from 1993 & up), 6210, 6210L, 6310, 6310L, 6310S, (6400 from 1993 and up with 4-276 dsl), (6400L from 1993 & up), 6400SP, 6405, 6410, 6410L, 6410S, (6500 from 1993 & up), 6500L, 6510L. Replaces 1107863, 1362312, 1367075, 1107871, 1998367, 0.

(Part No: SND0044) $121.37. This 2 Terminal Switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts. Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread. It is 21/32 inch over all length.

Check measurements before ordering if using as a universal part. Applications include Ether Switch, Horn Button, Cold Start, Starter Switch and Manifold Heater Switch. Replaces: AR46184, AR47373, AR47374, R39554, R39554. (Part No: R7994) $11.25 Engine Gaskets. For 2940, 2950, 2955, 3050, 3140, 3150, 3155TS, 3155, 3255, 3350, 4420, 7440, 7445, 9900, 9910, 9920, 4530, 955, 1055, 1075, 975, 985, 444D, 570B, 55, 54, all 6.359D Diesel, 300 Series, 6 cylinder, Block #s R53260, R55035, R55351, R72970, R79280, T32346, 4.19' bore, 1.375' pin.

Major Overhaul Kit includes: Piston Liner kit, Main Bearings set, Crank Seals, Connecting Rod Bearings/Bushings/Bolts set, Cam Bushing, Gasket Overhaul set. When ordering, specify in comments Main Bearing Size of Standard,.010,.020 or.030, Thrust Bearing Size of Standard,.010,.020 or.030, Connecting Rod Bearing Size of Standard,.010,.020, or.030. (Part No: RE50784) $1443.16 Engine Parts. This Hydraulic Pump has 1 1/16' Left inlet, 7/8' Top Inlet, 1 5/8 Right Inlet, 1 1/16' Discharge.

Verify measuerments before ordering. It is used on 1550, 1640, 1750, 1830, 1840, 1850, 1950, 2030, 2040, 2130, 2140, 2155, 2250, 2350, 2355, 2440, 2450, 2510, 2520, 2550, 2555, 2630, 2640, 2650, 2750, 2755, 2840, 2850, 2855N, 2940, 2950, 2955, 300 Indust/Const, 3010, 3020, 3030, 3040, 3050, 3055, 3130, 3140, 3150, 3155, 3255, 3350, 3640, 3650, 4010, 4030, 500 Indust/Const, 5010, 600 Indust/Const, 9950 Cotton Picker, 9960 Cotton Picker, 9965 Cotton Picker, 9970 Cotton Picker. It replaces AR39168, AR90459, AR97872, R39695 (Part No: AR97872) $959.10. Rockshaft Cover Gasket Kit (Lift Cover) includes a metal gasket.

John Deere TRACTOR: 1040, 1140, 1350, 1640 (serial number 430, 000 and up), 1641, 1641F, 1750, 1840, 1850, 1950, 2040 (serial number 430, 000 and up), 2040S (serial number 430, 000 and up), 2140 (serial number 430, 000 and up), 2141, 2150, 2155, 2240, 2250, 2251, 2255, 2350, 2351, 2355, 2355N, 2440, 2450, 2541, 2550, 2555, 2640, 2650, 2651, 2750, 2755, 2840, 2850, 2855N, 2940, 2941, 2950, 2951, 2955 (before serial number 767517), 3040 (serial number 430, 000 and up), 3050, 3055, 3140 (serial number 430, 000 and up), 3141, 3150, 3155, 3255, 3350, 3351, 3640, 3641, 3650, 3651, 840, 940. Replaces AL57974 (Part No: AL57974) $50.77. Fits 1020, 1520, 1640, 1840, 1950N, 2020, 2030, 2040, 2040S, 2150, 2155, 2250, 2251N, 2350, 2355N, 2440, 2450, 2510, 2550, 2555, 2630, 2640, 2650, 2750, 2755, 2840, 2850, 2855N, 2940, 2950, 300B, 300D, 301A, 302, 302A, 3040, 310 (SN# 237997 & below), 3130 (SN# 186270 & above), 3140, 3150 (STD Duty), 3230, 3350 (Std Duty), 4000 (SN# 201000 & above), 401B, 401C, 4020 (SN# 201000 & above), 4030, 4040, 4230, 4240, 4430, 6403, 7405, 300, 301, 310, 380, 400, 401, 480, 480A, and 480B. Replaces the part number R49839. Uses wheel bolt part number WB916. Please note that this hub uses a press in cap part# R50992 available only from John Deere.

(Part No: R49839) $66.73. This Spindle Dust Seal Measures: 44.6mm (1.76 inches) Inside Diameter, 59.78mm (2.35 inches) Outside Diameter.

Note, this seal can be felt as shown, or cork depending on availability. Used on John Deere TRACTOR: 1010 (SINGLE ROW CROP, SN 000), 1020, 1030, 1040, 1120, 1130, 1140, 1350, 1520, 1530, 1550, 1630, 1750, 1850, 1950, 2020, 2030, 2040, 2120, 2150, 2155, 2240, 2250, 2255 (SWEPT BACK AXLE), 2350 (LOWPROFILE), 2355 (MID-HI AXLE), 2355N, 2440, 2550, 2555 (MID-HI AXLE), 2630, 2640, 2755 (MID-HI AXLE), 3350, 320 (STD AXLES), 330 (STD AXLES), 40 (SERIAL NUMBER 69404 AND UP W/ STD AXLE), 420 (STD AXLES), 430 (STD AXLES), 820(3 Cyl.), 830(3 Cyl.), 940. Replaces M2282T (Part No: M2282T) $4.50. This Spindle Thrust Bearing Measures: 35.3mm (1.39 inches) Inside Diameter, 58.5mm (2.30 inches) Outside Diameter, 16mm (0.63 inches) Wide. Used on John Deere TRACTOR: 1010 (SINGLE ROW CROP, SN 000), 1020, 1030, 1040, 1120, 1130, 1140, 1350, 1520, 1530, 1550, 1630, 1750, 1850, 1950, 2020, 2030, 2040, 2120, 2150, 2155, 2240, 2250, 2255 (SWEPT BACK AXLE), 2350 (LOWPROFILE), 2355 (MID-HI AXLE), 2355N, 2440, 2550, 2555 (MID-HI AXLE), 2630, 2640, 2755 (MID-HI AXLE), 3350, 320 (STD AXLES), 330 (STD AXLES), 40 (SERIAL NUMBER 69404 AND UP W/ STD AXLE), 420 (STD AXLES), 430 (STD AXLES), 820(3 Cyl.), 830(3 Cyl.), 940. Replaces JD8407, JD2407, AH548R, JD8407HQQ, QX38497, 04271AB, VT2729, A30054, 441242C1 (Part No: JD8407) $8.69. This Spindle Thrust Washer is used on John Deere TRACTOR: 1010 (SINGLE ROW CROP, SN 000), 1020, 1030, 1040, 1120, 1130, 1140, 1350, 1520, 1530, 1550, 1630, 1750, 1850, 1950, 2020, 2030, 2040, 2120, 2150, 2155, 2240, 2250, 2255 (SWEPT BACK AXLE), 2350 (LOWPROFILE), 2355 (MID-HI AXLE), 2355N, 2440, 2550, 2555 (MID-HI AXLE), 2630, 2640, 2755 (MID-HI AXLE), 3350, 320 (STD AXLES), 330 (STD AXLES), 40 (SERIAL NUMBER 69404 AND UP W/ STD AXLE), 420 (STD AXLES), 430 (STD AXLES), 820(3 Cyl.), 830(3 Cyl.), 940.

Replaces M2283T (Part No: M2283T) $1.77. For 1020, 1520, 1640, 1840, 2020, 2030, 2040, 2040S, 2150, 2155, 2250, 2350, 2355, 2440, 2450, 2550, 2555, 2630, 2640, 2650, 2750, 2755, 2840, 2850, 2940, 2950, 300, 301A, 302A, 3040, 310B, 3140, 3230, 400, 401, 4030, 4230, 440, 480A, 480B, 62140, (3150, 3350 all standard duty), 300B 310A after SN# 237998, 2855 with swept back, 310 with SN# below 237997, 3130 with SN# above 186270. Wheel Bearing Kit for 1 wheel. Kit contains:25590(Cone), 25520(Cup), M88048(Cone), M88010(Cup), 23342(Seal), R26632(Seal Retainer). (Part No: WBKJD7) $48.59.

This wheel bolt fits the following John Deere tractor models using the R49839 and R47076 hubs: 1020, 1520, 1640, 1840, 1950N, 2020, 2030, 2040, 2040S, 2150, 2155, 2250, 2251N, 2350, 2355N, 2440, 2450, 2510, 2550, 2555, 2630, 2640, 2650, 2750, 2755, 2840, 2850, 2855N, 2940, 2950, 300B, 300D, 301A, 302, 302A, 3040, 310 (SN# 237997 & below), 3130 (SN# 186270 & above), 3140, 3150 (STD Duty), 3230, 3350 (Std Duty), 4000 (SN# 201000 & above), 401B, 401C, 4020 (SN# 201000 & above), 4030, 4040, 4230, and 4240. It has an overall length of 1.81 inches, a thread size of 9/16 – 18 UNF, and thread length of 1.12 inches. Replaces part numbers: AA4173R and AT11920. (Part No: WB916) $1.49 Universal Parts and Accessories Category: Accessories / Supplies Accessories / Supplies. Lucas Hub Oil was formulated to stop leaks in steering axles and trailer hubs on heavy duty trucks.

It also allows hubs to run on a marginal amount of oil in case of a blown seal or poor maintenance. It is an excellent gear lube for racing or heavy duty applications. Key benefits slows leaks, prevents downtime, extremely heat resistant, Very long lasting. (Part No: LU10088) $10.56 Electrical System - Don't see the Alternator you need for your tractor?

We have many alternators not listed on this website (for tractors 1953 & newer). Just call us at 800-853-2651. Lucas Assembly Lube (4 oz). Designed to be used as an initial lubricant to metal surfaces.

It mixes with any oil and will not plug filters. This product clings to all surfaces and is an excellent rust inhibitor, allowing long term storage for all parts. It is useful wherever tension or torque is applied. Key Benefits are: Use to pre lube camshaft, bearings, lifters and valve train. Prevents seizing, galling and scuffing perfect for engine lding, super slick and tacky, easy to use, excellent rust inhibitor, excellent for long term storage, contains Zinc, Moly and other extreme pressure additives for maximum protection during engine break-in. (Part No: 10152) $5.00 Engine Parts - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor). NOTE Engine Rings - Don't see the correct ring set for your tractor?

Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size & type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3.

Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32'), 4. Number and size of oil rings for each piston (Ex: (1) 5/32'). NOTE Exhaust System. Lucas Fuel Treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency.

Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions. Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.A powerful blend of oils and additives that contain no SOLVENTS. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion. (Part No: LU10003) $10.67.

Comes assembled complete with hardware. Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed.

An additional shipping charge of $60 will apply due to the weight of this item. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: HF141101) $227.70. Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inches to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405.

Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32. Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inch diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork.

For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32. Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork.

For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Part No: BH215) $106.08. 6 inch x 9 inch tail wheel assembly with laminated tire, less hub. 4 inch pilot, 5 bolt holes, 5-1/2 inch bolt circle. 5-1/4 inches wide, 21 inch outside diameter, 74#. Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F.

(Part No: 294) $124.93. 60 inches wide x 65 inches long, molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars, no mounting bolts pass through molding. Available in green, white, orange, blue, or red. Please specify in comments section which color you need. Hardware to mount to your ROPS sold separately.

Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.

(Part No: B257X) $430.31. 45 inches wide x 60 inches long. Molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars NO mounting bolts pass through molding.

Available in white, green, orange, blue, and red please specify in comments section which color you prefer. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257XSTD) $374.50. Deluxe Umbrella comes with universal mounting bracket.

Four spring steel bows are locked into place with individual spring clips, providing ease of operation and a rigid framework. Frame constructed of tubular steel.

All metal parts are zinc plated for rust resistance. 54 inch square cover is made of durable polyester material. Each corner is double reinforced. AVAILABLE IN RED, YELLOW, ORANGE, WHITE or BLUE. State color desired in comments section of order form when ordering. (Part No: TU56-X) $155.22. A pure petroleum multi-use oil supplement.

Controls noise, heat and wear in manual transmissions and differentials. Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine.

It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures. Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil.

Since it is pure petroleum. Key Features Increase oil life at least 50% longer, Reduces oil consumption, Eliminates dry starts, Raises oil pressure, and Increases power and miles per gallon. (Part No: LU10001) $15.12 PTO / Driveline. AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes.

1-3/8 inch 6 spline Q.D. Tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke.

1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch).

Verify length before ordering. (Part No: AB4111WY) $187.82. AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end.

John Deere 3350 Manual

1-3/8 inch 6 spline Q.D. Tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length.VERIFY LENGTH BEFORE ORDERING.

(Part No: AB4111K33) $288.01. Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR.

Color is Black. Additional $30 shipping due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1050ATSP) $82.25. BLUE Universal application leatherette suspension seat. For most compact, agricultural and industrial tractors.

Adjustable base for 5 different mounting angles, internal suspension weight adjustment, special slotted base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, adjustable slide track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL.

PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLUE.

Add $15 additional shipping per seat due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1060ATSP) $89.37. Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL.

PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLACK.

(Part No: TS1075ATSP) $82.25.YELLOW. Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR.

Color is John Deere Yellow. Add $15.00 additional shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1040ATSP) $88.39 Sheet Metal / Body Parts. This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761.

This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn power Steering with an Eaton Pump.

Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures.670 inches. The shaft length, where the pulley mounts measures.575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM.

(Part No: S03-1003) $384.33. With embroidered John Deere logo. (Part No: JDGR) $19.95 Call 800-853-2651 to Order Or Click the 'Add to Cart' Button Customer Service Monday - Friday 9:00-6:30pm EST Order online anytime!

Your Shopping is YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us!

Copyright © 1997-2018 Yesterday's Tractor Co. Antique Tractor Headquarters All Rights Reserved TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. Products and within the Yesterday's Tractor Co. Websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation.

Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.